A New Viscoelastic Model for Polycarbonate Compressing Flow

Authors

  • Wei Cao National Engineering Research Center of Mold &Die, Zhengzhou University, Zhengzhou, Henan, 450002,China
  • Yaqiang Shen Shenzhen Zhaowei Machinery & Electronics CO., LTD., Shenzhen, 518103,China
  • Shixun Zhang National Engineering Research Center of Mold &Die, Zhengzhou University, Zhengzhou, Henan, 450002,China
  • Tao Wang Beijing Institute of Aeronautical Materials, Beijing, 100095,China
  • Yakun Wu National Engineering Research Center of Mold &Die, Zhengzhou University, Zhengzhou, Henan, 450002,China
  • Changyu Shen National Engineering Research Center of Mold &Die, Zhengzhou University, Zhengzhou, Henan, 450002,China

DOI:

https://doi.org/10.30564/jmer.v1i1.252

Abstract

To overcome the weakness of conventional models in describing compressing flow especially in start and end stages the shear rate derivative was added to the right side of PTT constitutive equation. The ability of describing the well-known ‘shear shinning’ and ‘stretch harden’ phenomena was first illustrated by theoretical analysis. Then the governing equations for compressing flow were established in terms of incompressible and isothermal fluid, and the numerical method was constructed to discretize the equations and get the compressing flow solutions. The experiments with four melt temperatures were conducted and the corresponding simulations were performed. The better agreements with experimental data indicates the modified PPT model is superior to the original PTT model in prediction of compressing flow. In addition, the proposed model is also validated with low and high compressing speed experiments.

Keywords:

Viscoelastic, Constitutive model, Compressing flow, Numerical simulation

References

[1] A.I. Isayev and R.K. Upadhyay, Injection and Compression Molding Fundamentals, Marcel Deker, New York, 1987.

[2] W. Cao, T. Wang, Y. Yan, et al. Evaluation of typical rheological models fitting for polycarbonate squeeze flow. J. Applied Polymer Sci. 2015, 132(29): 42279(1-8).

[3] N. Phan-Thien, and R.I. Tanner, An analytical solution for fully developed from network theory, J. Non-Newtonian Fluid Mech. 1977, 2: 353-365.

[4] N. Phan-Thien, A non-linear network viscoelastic model, J. Rheo. 1978, 22(3): 259-283.

[5] B. Debbaut, Non-isothermal and viscoelastic effects in the squeeze flow between infinite plates, J. Non-Newtonian Fluid Mech. 2001, 98(1): 15–31.

[6] J. D. Sherwood, Model-free inversion of squeeze-flow rheometer data, J. Non-Newtonian Fluid Mech. 2005, 129(2): 61-65.

[7] J. H. Kim and K. Hyun, A new instrument for dynamic helical squeeze flow which superposes oscillatory shear and oscillatory squeeze flow, Rev. Sci. Instrum. 2012, 83(8): 085105(1-8).

[8] D. Cheneler, J. Bowen, M.C.L. Ward, M.J. Adams, Micro squeeze flow rheometer for high frequency analysis of nano-litre volumes of viscoelastic fluid, Microelectronic Engineering 2011, 88(8): 1726-1729.

[9] D. Cheneler, The Design and Analysis of a Micro Squeeze Flow Rheometer, Ph.D. Thesis, Department of Mechanical Engineering, University of Birmingham, UK, 2010.

[10] R. G. Larson, A critical comparison of constitutive equations for polymer melts, J. Non-Newtonian Fluid Mech. 1987, 23(87): 249-268.

[11] M. Aboubacar, H. Matallah, M.F. Webster, Highly elastic solutions for Oldroyd-B and Phan-Thien/Tanner fluids with a finite volume/element method: planar contraction flows, J. Non-Newtonian Fluid Mech. 2002, 103(1): 65–103.

[12] A.S. Palmer and T.N. Phillips, Numerical approximation of the spectra of Phan-Thien Tanner liquids, Numerical Algorithms 2005, 38(1-3): 133-153.

[13] W. Cao, C. Shen, C. Zhang et al, Computing flow-induced stresses of injection molding based on the Phan–Thien–Tanner model, Archive of Applied Mechanics 2008, 78(5): 363-377.

[14] Y. Kobayashi, Y. Otsuki, H. Kanno, Y. Hanamoto, T. Kana, Crystallization of Polypropylene Near the Surface in Injection-Molded Plaques: A Comparison of Morphology and a Numerical Analysis, POLYM. ENG. SCI. 2011, 51(7): 1236–1244.

[15] O. James, On the Formulation of Rheological Equations of State, Proceedings of the Royal Society of London. Series A, Mathematical and Physical Sciences 1950, 200: 523–541.

Downloads

Issue

Vol. 1 , Iss. 1 (September 2018)

Article Type

Articles

License

Copyright © 2018 Wei Cao, Yaqiang Shen, Shixun Zhang, Tao Wang, Yakun Wu, Changyu Shen

Creative Commons License

This is an open access article under the Creative Commons Attribution-NonCommercial 4.0 International (CC BY-NC 4.0) License.