The Anneal Temperature Effect on the BTO and NZFO Flims and Their Capacitance - Inductance Integrated Device

Authors

  • Zhen Zheng State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China
  • Yuhao Shi State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China
  • Xinyu Liang State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China
  • Chunqing Wang State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China

DOI:

https://doi.org/10.30564/ssid.v1i1.606

Abstract

In this paper, a novel capacitor-inductor integrated structure was proposed. The dielectric material BaTiO3 (BTO) and ferromagnetic material Ni0.5Zn0.5Fe2O4 (NZFO) was prepared by sol-gel method. Phase composition and morphology of the thin films were characterized by XRD, SEM and AFM. The effect of annealing temperature on film crystallinity, surface morphology, dielectric properties and ferromagnetism were investigated. When the annealing temperature was 700 °C, the BTO film and the NZFO film got the better dielectric properties and ferromagnetic properties. Then the BTO thin film was spin-coated on the substrate, and the NZFO thin film was in-situ sintered on the BTO thin film. The composite film possessed both ferromagnetism and dielectric properties. Finally, an inductive coil was fabricated on the BTO/NZFO composite film to produce a capacitance and inductance integrated device.

Keywords:

Capacitor-inductor, Integrated device, BTO film, NZFO film, Anneal temperature

References

[1] He X, Chen Y, Wang S, et al. Enhancing inductance of spiral copper inductor with BaFe12O19/poly (phenylene oxide) composite as an embedded magnetic core[J]. Composites Part B: Engineering, 2018, 138: 232-242.

[2] Anthony R , Wang N , Casey D P , et al. MEMS based fabrication of high - frequency integrated inductors on Ni-Cu-Zn ferrite substrates[J]. Journal of Magnetism & Magnetic Materials, 2016, 406: 89-94.

[3] Dai G, Zhang J. Concept and architecture technology of integrated microsystems [J]. Microelectronics, 2016, 46(1): 101-106.

[4] Chao S, Dogan F. BaTiO3–SrTiO3 layered dielectrics for energy storage[J]. Materials Letters, 2011, 65(6): 978-981.

[5] Khirade P P, Birajdar S D, Raut A V, et al. Multiferroic iron doped BaTiO3 nanoceramics synthesized by sol-gel auto combustion: influence of iron on physical properties[J]. Ceramics International, 2016, 42(10): 12441-12451.

[6] Choudhury A. Dielectric and piezoelectric properties of polyetherimide/BaTiO3 nanocomposites[J]. Materials Chemistry and Physics, 2010, 121(1-2): 280-285.

[7] Nayak S, Kumar Chaki T, Khastgir D. Development of poly (dimethylsiloxane) / BaTiO3 nanocomposites as dielectric material[C]. Advanced Materials Research. Trans Tech Publications, 2013, 622: 897-900.

[8] Dang Z M, Yu Y F, Xu H P, et al. Study on microstructure and dielectric property of the BaTiO3/epoxy resin composites[J]. Composites Science and Technology, 2008, 68(1): 171-177.

[9] Dang Z M, Lin Y Q, Xu H P, et al. Fabrication and dielectric characterization of advanced BaTiO3/polyimide nanocomposite films with high thermal stability[J]. Advanced Functional Materials, 2008, 18(10): 1509-1517.

[10] Zhou T, Zha J W, Cui R Y, et al. Improving dielectric properties of BaTiO3/ ferroelectric polymer composites by employing surface hydroxylated BaTiO3 nanoparticles[J]. ACS applied materials & interfaces, 2011, 3(7): 2184-2188.

[11] Cernea M, Andronescu E, Radu R, et al. Sol–gel synthesis and characterization of BaTiO3-doped (Bi0.5Na0.5)TiO3 piezoelectric ceramics[J]. Journal ofAlloys and Compounds, 2010, 490(1-2): 690-694.

[12] Ashiri R, Nemati A, Ghamsari M S. Crack-Free nanostructured BaTiO3, thin films prepared by sol–gel dip-coating technique[J]. Ceramics International, 2014, 40(6): 8613-8619.

[13] Li J, Zhu G, Xu H, et al. Preparation, structure and dielectric properties of substrate-free BaTiO3, thin films by sol–gel method[J]. Journal of Materials Science Materials in Electronics, 2017, 28(17): 1-5.

[14] Whittam, J., Hector, A. L., Kavanagh, C., et al.Combination of solid state and electrochemical impedance spectroscopy to explore effects of porosity in sol-gel derived BaTiO3 thin films[J]. ACS Omega. 2018, 42(1): 20-22.

[15] Tripkovic D, Vukmirovic J, Bajac B, et al. Inkjet patterning of in situ, sol–gel derived barium titanate thin films[J]. Ceramics International, 2016, 42(1): 1840-1846.

[16] Suematsu K, Arimura M, Uchiyama N, et al. High-performance dielectric thin film nanocomposites of barium titanate and cyanoethyl pullulan: controlling the barium titanate nanoparticle size using a sol–gel method[J]. RSC Advances, 2016, 6(25): 20807-20813.

[17] ShinS H, Choi S Y, Lee M H, et al. High-performance piezoelectric nanogenerators via imprinted sol-gel BaTiO3 nanopillar array[J]. Acs Applied Materials & Interfaces, 2017, 9(47): 41099.

[18] Wang Y L, Wu W J, Mao W D, et al. Fast sintering soft ferrite materials at low temperature [J]. Journal of Inorganic Materials, 2003, 18(3): 601-605.

[19] Ghafoor A , Khan M A , Islam M U , et al. Structural and electromagnetic studies of Ni0.7Zn0.3Ho2xFe2−2xO4 ferrites[J]. Ceramics International, 2016, 42(12): 14252-14256.

[20] Gao J, Cui Y, Yang Z. The magnetic properties of NixZn1−xFe2O4, films fabricated by alternative sputtering technology[J]. Materials Science & Engineering B, 2004, 110(2): 111-114.

[21] Liu Y, Li Y, Zhang H, et al. Structural and magnetic properties of NiZn-ferrite thin films prepared by radio frequency magnetron sputtering[J]. Journal of Applied Physics, 2011, 109(7): 739.

[22] Zhong X, Phuoc N N, Soh W T, et al. Dynamic magnetization of NiZn ferrite doped FeSiAl thin films fabricated by oblique sputtering[J]. Journal of Magnetism & Magnetic Materials, 2017, 432: 373-381.

[23] Hashi S, Takada N, Nishimura K, et al. Fabrication technique for over 10-μm-thick ferrite particulate film at room temperature[J]. Magnetics IEEE Transactions on, 2005, 41(10): 3487-3489.

[24] Lee J J, Hong Y K, Bae S, et al. High-quality factor Ni-Zn ferrite planar inductor[J]. IEEE Transactions on Magnetics Mag, 2010, 46(6): 2417-2420.

[25] Li L, Peng L, Li Y, et al. Structure and magnetic properties of Co-substituted NiZn ferrite thin films synthesized by the sol–gel process[J]. Journal of Magnetism & Magnetic Materials, 2012, 324(1): 60-62.

[26] Gao P, Rebrov E V, Verhoeven T M W G M, et al. Structural investigations and magnetic properties of sol-gel Ni0.5Zn0.5Fe2O4 thin films for microwave heating[J]. Journal of Applied Physics, 2010, 107(4): 5223.

[27] Yusuf Y, Azis R S, Kanagesan S, et al. Microstructure and magnetic properties of Ni-Zn ferrite thin film synthesized using sol-gel and spin-coating technique[J]. Journal of the Australian Ceramic Society, 2017, 53(8): 1-8.

[28] Li B , Wang C , Liu W , et al. Synthesis of Co-doped barium strontium titanate nanofibers by sol–gel/electrospinning process[J]. Materials Letters, 2012, 75: 207-210.

Downloads

How to Cite

Zheng, Z., Shi, Y., Liang, X., & Wang, C. (2019). The Anneal Temperature Effect on the BTO and NZFO Flims and Their Capacitance - Inductance Integrated Device. Semiconductor Science and Information Devices, 1(1), 2–6. https://doi.org/10.30564/ssid.v1i1.606

Issue

Article Type

Article